Follow this procedure to test, rework, and program a new Ubertooth One.  For
reference, see ubertooth-one-hardware/ubertooth-one-assembly.pdf and
ubertooth-one-hardware/ubertooth-one-schematic.pdf in the release package or
use KiCad to view the design files located in hardware/ubertooth-one.


Required Equipment

  - Equipment Under Test (EUT): Ubertooth One with 2 dBi antenna

  - Personal Computer (PC) with two open USB ports

  - Pogoprog, a serial programmer for Ubertooth One

  - USB Mini-B cable to connect Pogoprog to PC

  - USB A extension cable or USB hub to allow access to underside of Ubertooth
	One while it is plugged into the PC

  - A Bluetooth device such as a mobile phone

  - Multi-meter (voltmeter and continuity tester)


Required Software

  - lpc21isp


Visual Inspection

  1. Check EUT for missing components.

  2. Check that components are installed with the correct orientation and
  placement.

  3. Check in particular that R1 and C12 are not soldered together (one side,
  GND, may be together, but the side closest to U1 should not be).


Electrical Inspection

  1. Verify no conductivity across C18.

  2. Verify no conductivity across C22.

  3. Verify no conductivity across C32.
 
  If shorts are detected, carefully inspect (in order) the three capacitors
  listed above, the voltage regulator (U7), bypass capacitors, and all IC pins.


Power On EUT

  1. Connect to EUT the 2 dBi antenna.  Check that the antenna fully screws
  onto the RP-SMA connector.

  2. Plug EUT in to PC with USB A extension cable or USB hub.

  3. The "RST" LED (D5) should be illuminated.  No other LED should be fully
  illuminated, though they may be dimly lit.  D5 indicates that U4 has been
  powered on and passed reset.  If D5 does not illuminate, check D5, R8, R9,
  and pins 11 and 14 on U4.


Program EUT with assembly_test Firmware

  1. Ensure EUT is plugged into PC.

  2. Plug Pogoprog into PC with USB Mini-B cable.

  3. Hold Pogoprog against the "PROGRAM" pads on the underside of EUT as shown
  in the photograph:

    http://ubertooth.sourceforge.net/hardware/program/

  4. on the PC, execute:

    $ make program

  If you have not yet compiled the assembly_test firmware, you will need to
  have a gcc/arm environment set up.  See:

    http://ubertooth.sourceforge.net/firmware/develop/

  5. The 'make program' command will indicate "Download Finished . . . Now
  launching the brand new code" if successful.  If it was not successful, check
  the orientation and contact between the Pogoprog and sample Ubertooth One,
  make sure both are plugged in, and try again.


Automated Test

  1. Unplug EUT from PC and plug back in.

  2. "RST" LED (D5) should illuminate immediately and remain on throughout this
  test.

  3. "TX" LED (D2), "RX" LED (D3), and "USR" LED (D4) should flash twice
  together.  Flashing indicates that the test program is executing on U4.  If
  any of the three LEDs do not flash, check that LED, the adjacent resistor,
  and pins 73, 74, and 75 of U4.

  4. Next, "1V8" LED (D1) should illuminate and remain on.  This indicates that
  U3 is powered on.  If D1 does not illuminate, check D1, R3, R4, U7, and pin
  72 of U4.

  5. Next, "TX" LED (D2) should flash twice and then illuminate and remain on.
  This indicates that U4 is able to communicate with U3.  If D2 does not flash
  and illuminate, check pins 25-35 on U3 and pins 53, 54, 58, 59, 60, and 70 on
  U4.  Check that there is a 1.8 Volt potential across C18.  Check that there
  is a 3.3 Volt potential across C25.

  6. Next, "RX" LED (D3) should flash four times quickly and then illuminate
  and remain on.  This indicates that the 16 MHz crystal oscillator is active
  and supplying clock to both U3 and U4.  If D3 does not flash and illuminate,
  check X1, C19, C21, C29, C31, pins 21, 42, and 43 on U3, and pins 19 and 20
  on U4.

  7. At this point, four LEDs (D1, D2, D3, and D5) should all be on.

  8. Use a mobile phone or other Bluetooth device approximately 1 meter away
  from EUT to initiate an inquiry.  This function is typically called “search
  for new Bluetooth devices” or similar.

  9. During the inquiry, "USR" LED (D4) may flash and should then illuminate
  and remain on.  If D4 flashes but does not remain on after the inquiry, this
  indicates that RF performance is poor.  If D4 does not flash at all, this
  indicates a total RF failure.  Check that a 2 dBi antenna is securely
  connected to P1.  Check L1, L2, C1, C3, and C5.  Check all pins on U1 and U3.
  Check R1, R2, and R17.  Check all bypass capacitors around U1 and U3.  Check
  pins 50, 51, 61, 62, 63, 64, 65, 68, and 69 on U4.

  10. After D4 illuminates, the "USB" LED (D6) may flash and should then
  illuminate and remain on.  This indicates that the PC has established USB
  communication with EUT.  With some non-Linux operating systems, D6 may not
  illuminate.  Depending on the OS running on the PC, you might see a "found
  new hardware" or "install device driver software" dialog instead of
  illumination of D6.  You should be able to use operating system logging or
  reporting (e.g. dmesg on Linux) to see that a USB device with the product
  name "ubertooth assembly_test" has been detected.  This indicates success.
  Cancel any dialog and visually inspect D6 and R15.

  11. If all six LEDs are on (with the possible exception of D6 as mentioned
  above), the Automated Test is successful.  To repeat the Automated Test,
  unplug EUT from PC and plug in again.


Test Complete

  If your Ubertooth One has passed the assembly test procedure, the recommended
  next steps are:

  1. Install the USB bootloader on your Ubertooth One.  See:

	firmware/bootloader/README

  2. Use the bootloader to install the bluetooth_rxtx application firmware.
  See:

    host/usb_dfu/README

  3. Follow the Getting Started guide:

    http://ubertooth.sourceforge.net/usage/start/