New upstream version 0.7+20180830git0b7a184

1 files changed, 136 insertions, 0 deletions

diff --git a/techlibs/greenpak4/cells_sim_wip.v b/techlibs/greenpak4/cells_sim_wip.v
new file mode 100644
index 00000000..5261b12d
--- /dev/null
+++ b/techlibs/greenpak4/cells_sim_wip.v
@@ -0,0 +1,136 @@
+
+//Cells still in this file have INCOMPLETE simulation models, need to finish them
+
+module GP_DCMP(input[7:0] INP, input[7:0] INN, input CLK, input PWRDN, output reg GREATER, output reg EQUAL);
+	parameter PWRDN_SYNC = 1'b0;
+	parameter CLK_EDGE = "RISING";
+	parameter GREATER_OR_EQUAL = 1'b0;
+
+	//TODO implement power-down mode
+
+	initial GREATER = 0;
+	initial EQUAL = 0;
+
+	wire clk_minv = (CLK_EDGE == "RISING") ? CLK : ~CLK;
+	always @(posedge clk_minv) begin
+		if(GREATER_OR_EQUAL)
+			GREATER <= (INP >= INN);
+		else
+			GREATER <= (INP > INN);
+
+		EQUAL <= (INP == INN);
+	end
+
+endmodule
+
+module GP_EDGEDET(input IN, output reg OUT);
+
+	parameter EDGE_DIRECTION = "RISING";
+	parameter DELAY_STEPS = 1;
+	parameter GLITCH_FILTER = 0;
+
+	//not implemented for simulation
+
+endmodule
+
+module GP_RCOSC(input PWRDN, output reg CLKOUT_HARDIP, output reg CLKOUT_FABRIC);
+
+	parameter PWRDN_EN = 0;
+	parameter AUTO_PWRDN = 0;
+	parameter HARDIP_DIV = 1;
+	parameter FABRIC_DIV = 1;
+	parameter OSC_FREQ = "25k";
+
+	initial CLKOUT_HARDIP = 0;
+	initial CLKOUT_FABRIC = 0;
+
+	//output dividers not implemented for simulation
+	//auto powerdown not implemented for simulation
+
+	always begin
+		if(PWRDN) begin
+			CLKOUT_HARDIP = 0;
+			CLKOUT_FABRIC = 0;
+		end
+		else begin
+
+			if(OSC_FREQ == "25k") begin
+				//half period of 25 kHz
+				#20000;
+			end
+
+			else begin
+				//half period of 2 MHz
+				#250;
+			end
+
+			CLKOUT_HARDIP = ~CLKOUT_HARDIP;
+			CLKOUT_FABRIC = ~CLKOUT_FABRIC;
+		end
+	end
+
+endmodule
+
+module GP_RINGOSC(input PWRDN, output reg CLKOUT_HARDIP, output reg CLKOUT_FABRIC);
+
+	parameter PWRDN_EN = 0;
+	parameter AUTO_PWRDN = 0;
+	parameter HARDIP_DIV = 1;
+	parameter FABRIC_DIV = 1;
+
+	initial CLKOUT_HARDIP = 0;
+	initial CLKOUT_FABRIC = 0;
+
+	//output dividers not implemented for simulation
+	//auto powerdown not implemented for simulation
+
+	always begin
+		if(PWRDN) begin
+			CLKOUT_HARDIP = 0;
+			CLKOUT_FABRIC = 0;
+		end
+		else begin
+			//half period of 27 MHz
+			#18.518;
+			CLKOUT_HARDIP = ~CLKOUT_HARDIP;
+			CLKOUT_FABRIC = ~CLKOUT_FABRIC;
+		end
+	end
+
+endmodule
+
+module GP_SPI(
+	input SCK,
+	inout SDAT,
+	input CSN,
+	input[7:0] TXD_HIGH,
+	input[7:0] TXD_LOW,
+	output reg[7:0] RXD_HIGH,
+	output reg[7:0] RXD_LOW,
+	output reg INT);
+
+	initial RXD_HIGH = 0;
+	initial RXD_LOW = 0;
+	initial INT = 0;
+
+	parameter DATA_WIDTH = 8;		//byte or word width
+	parameter SPI_CPHA = 0;			//SPI clock phase
+	parameter SPI_CPOL = 0;			//SPI clock polarity
+	parameter DIRECTION = "INPUT";	//SPI data direction (either input to chip or output to host)
+	//parallel output to fabric not yet implemented
+
+	//TODO: write sim model
+	//TODO: SPI SDIO control... can we use ADC output while SPI is input??
+	//TODO: clock sync
+
+endmodule
+
+//keep constraint needed to prevent optimization since we have no outputs
+(* keep *)
+module GP_SYSRESET(input RST);
+	parameter RESET_MODE = "EDGE";
+	parameter EDGE_SPEED = 4;
+
+	//cannot simulate whole system reset
+
+endmodule