1 files changed, 110 insertions, 0 deletions
diff --git a/techlibs/greenpak4/cells_sim_ams.v b/techlibs/greenpak4/cells_sim_ams.v
new file mode 100644
index 00000000..7f8b3de3
--- /dev/null
+++ b/techlibs/greenpak4/cells_sim_ams.v
@@ -0,0 +1,110 @@
+`timescale 1ns/1ps
+
+/*
+ This file contains analog / mixed signal cells, or other things that are not possible to fully model
+ in behavioral Verilog.
+
+ It also contains some stuff like oscillators that use non-synthesizeable constructs such as delays.
+ TODO: do we want a third file for those cells?
+ */
+
+module GP_ABUF(input wire IN, output wire OUT);
+
+	assign OUT = IN;
+
+	//must be 1, 5, 20, 50
+	//values >1 only available with Vdd > 2.7V
+	parameter BANDWIDTH_KHZ = 1;
+
+endmodule
+
+module GP_ACMP(input wire PWREN, input wire VIN, input wire VREF, output reg OUT);
+
+	parameter BANDWIDTH = "HIGH";
+	parameter VIN_ATTEN = 1;
+	parameter VIN_ISRC_EN = 0;
+	parameter HYSTERESIS = 0;
+
+	initial OUT = 0;
+
+endmodule
+
+module GP_BANDGAP(output reg OK);
+	parameter AUTO_PWRDN = 1;
+	parameter CHOPPER_EN = 1;
+	parameter OUT_DELAY = 100;
+
+endmodule
+
+module GP_DAC(input[7:0] DIN, input wire VREF, output reg VOUT);
+
+	initial VOUT = 0;
+
+	//analog hard IP is not supported for simulation
+
+endmodule
+
+module GP_LFOSC(input PWRDN, output reg CLKOUT);
+
+	parameter PWRDN_EN = 0;
+	parameter AUTO_PWRDN = 0;
+	parameter OUT_DIV = 1;
+
+	initial CLKOUT = 0;
+
+	//auto powerdown not implemented for simulation
+	//output dividers not implemented for simulation
+
+	always begin
+		if(PWRDN)
+			CLKOUT = 0;
+		else begin
+			//half period of 1730 Hz
+			#289017;
+			CLKOUT = ~CLKOUT;
+		end
+	end
+
+endmodule
+
+module GP_PGA(input wire VIN_P, input wire VIN_N, input wire VIN_SEL, output reg VOUT);
+
+	parameter GAIN = 1;
+	parameter INPUT_MODE = "SINGLE";
+
+	initial VOUT = 0;
+
+	//cannot simulate mixed signal IP
+
+endmodule
+
+module GP_PWRDET(output reg VDD_LOW);
+	initial VDD_LOW = 0;
+endmodule
+
+module GP_VREF(input VIN, output reg VOUT);
+	parameter VIN_DIV = 1;
+	parameter VREF = 0;
+	//cannot simulate mixed signal IP
+endmodule
+
+module GP_POR(output reg RST_DONE);
+	parameter POR_TIME = 500;
+
+	initial begin
+		RST_DONE = 0;
+
+		if(POR_TIME == 4)
+			#4000;
+		else if(POR_TIME == 500)
+			#500000;
+		else begin
+			$display("ERROR: bad POR_TIME for GP_POR cell");
+			$finish;
+		end
+
+		RST_DONE = 1;
+
+	end
+
+endmodule