initial import

1 files changed, 154 insertions, 0 deletions

diff --git a/tests/asicworld/code_hdl_models_uart.v b/tests/asicworld/code_hdl_models_uart.v
new file mode 100644
index 00000000..40205250
--- /dev/null
+++ b/tests/asicworld/code_hdl_models_uart.v
@@ -0,0 +1,154 @@
+//-----------------------------------------------------
+// Design Name : uart 
+// File Name   : uart.v
+// Function    : Simple UART
+// Coder       : Deepak Kumar Tala
+//-----------------------------------------------------
+module uart (
+reset          ,
+txclk          ,
+ld_tx_data     ,
+tx_data        ,
+tx_enable      ,
+tx_out         ,
+tx_empty       ,
+rxclk          ,
+uld_rx_data    ,
+rx_data        ,
+rx_enable      ,
+rx_in          ,
+rx_empty
+);
+// Port declarations
+input        reset          ;
+input        txclk          ;
+input        ld_tx_data     ;
+input  [7:0] tx_data        ;
+input        tx_enable      ;
+output       tx_out         ;
+output       tx_empty       ;
+input        rxclk          ;
+input        uld_rx_data    ;
+output [7:0] rx_data        ;
+input        rx_enable      ;
+input        rx_in          ;
+output       rx_empty       ;
+
+// Internal Variables 
+reg [7:0]    tx_reg         ;
+reg          tx_empty       ;
+reg          tx_over_run    ;
+reg [3:0]    tx_cnt         ;
+reg          tx_out         ;
+reg [7:0]    rx_reg         ;
+reg [7:0]    rx_data        ;
+reg [3:0]    rx_sample_cnt  ;
+reg [3:0]    rx_cnt         ;  
+reg          rx_frame_err   ;
+reg          rx_over_run    ;
+reg          rx_empty       ;
+reg          rx_d1          ;
+reg          rx_d2          ;
+reg          rx_busy        ;
+
+// UART RX Logic
+always @ (posedge rxclk or posedge reset)
+if (reset) begin
+  rx_reg        <= 0; 
+  rx_data       <= 0;
+  rx_sample_cnt <= 0;
+  rx_cnt        <= 0;
+  rx_frame_err  <= 0;
+  rx_over_run   <= 0;
+  rx_empty      <= 1;
+  rx_d1         <= 1;
+  rx_d2         <= 1;
+  rx_busy       <= 0;
+end else begin
+  // Synchronize the asynch signal
+  rx_d1 <= rx_in;
+  rx_d2 <= rx_d1;
+  // Uload the rx data
+  if (uld_rx_data) begin
+    rx_data  <= rx_reg;
+    rx_empty <= 1;
+  end
+  // Receive data only when rx is enabled
+  if (rx_enable) begin
+    // Check if just received start of frame
+    if (!rx_busy && !rx_d2) begin
+      rx_busy       <= 1;
+      rx_sample_cnt <= 1;
+      rx_cnt        <= 0;
+    end
+    // Start of frame detected, Proceed with rest of data
+    if (rx_busy) begin
+       rx_sample_cnt <= rx_sample_cnt + 1;
+       // Logic to sample at middle of data
+       if (rx_sample_cnt == 7) begin
+          if ((rx_d2 == 1) && (rx_cnt == 0)) begin
+            rx_busy <= 0;
+          end else begin
+            rx_cnt <= rx_cnt + 1; 
+            // Start storing the rx data
+            if (rx_cnt > 0 && rx_cnt < 9) begin
+              rx_reg[rx_cnt - 1] <= rx_d2;
+            end
+            if (rx_cnt == 9) begin
+               rx_busy <= 0;
+               // Check if End of frame received correctly
+               if (rx_d2 == 0) begin
+                 rx_frame_err <= 1;
+               end else begin
+                 rx_empty     <= 0;
+                 rx_frame_err <= 0;
+                 // Check if last rx data was not unloaded,
+                 rx_over_run  <= (rx_empty) ? 0 : 1;
+               end
+            end
+          end
+       end 
+    end 
+  end
+  if (!rx_enable) begin
+    rx_busy <= 0;
+  end
+end
+
+// UART TX Logic
+always @ (posedge txclk or posedge reset)
+if (reset) begin
+  tx_reg        <= 0;
+  tx_empty      <= 1;
+  tx_over_run   <= 0;
+  tx_out        <= 1;
+  tx_cnt        <= 0;
+end else begin
+   if (ld_tx_data) begin
+      if (!tx_empty) begin
+        tx_over_run <= 0;
+      end else begin
+        tx_reg   <= tx_data;
+        tx_empty <= 0;
+      end
+   end
+   if (tx_enable && !tx_empty) begin
+     tx_cnt <= tx_cnt + 1;
+     if (tx_cnt == 0) begin
+       tx_out <= 0;
+     end
+     if (tx_cnt > 0 && tx_cnt < 9) begin
+        tx_out <= tx_reg[tx_cnt -1];
+     end
+     if (tx_cnt == 9) begin
+       tx_out <= 1;
+       tx_cnt <= 0;
+       tx_empty <= 1;
+     end
+   end
+   if (!tx_enable) begin
+     tx_cnt <= 0;
+   end
+end
+
+endmodule